鋁高溫封閉劑

JR-S05高溫封閉劑

u 產品特性

1.封孔質量高，不起粉，不褪色；特別適合鋁氧化染色后的封閉處理。封閉后失重≤15mg/dm2.

2.槽液穩定性好，耐污染能力強，維護方便.

3.封閉劑消耗量少.

4.能使染色膜具較高的耐光牢度和耐候性.

u 開槽參數

JR-S05：5～10g/L

u 控制參數

Ni²⁺：0.8～1.3g/l       PH：5.5～6.2

溫度  ：85～95℃       時間  ： 1.0～1.5um/ min                          

u 維護和管理

1.每天檢驗槽液中的Ni2+濃度及pH值；并根據分析結果及時補加調整。處理100m2約消耗JR-S05：0.2～0.3Kg。

2.正常生產時PH值呈上升趨勢，每班需檢驗一次PH值并用稀醋酸/稀硫酸調整；如PH值偏低則說明帶入酸水過多，需控制染色前水洗PH值≥4.5，此時需用稀氨水/稀氫氧化鈉調整。

3.長期生產槽液或多或少會有沉淀物產生，要定期過濾或倒槽清理沉淀物。

u 包裝、貯存及保質期

20kg紙箱裝；避光、避酸堿、輕放、密封置干燥，陰涼處，防止泄漏。室溫存放1年。

 

JR-S05  Hot Sealing additive

u Product Features

1.Effective sealing without ash, no color fading particularly for thick anodized film. After sealing it’s weight loss test value ≤ 15mg/dm2

2.The high stability of bath solution, and strong resistance to contamination, and easy maintenance.

3. Low consumption of sealing agent and low cost.

4. Sealed anodizing film with higher gloss and weather resistance.

u Tank set up parameters

JR-S05：5～10g/L

u Coolling parameters

Ni²+：0.8～1.3g/l          PH：5.5～6.2

Temperature：85～95℃     Time：1.0～1.5um/ min                          

u Maintenance and coolling

1.Analyse the bath conceation of Ni2+ and PH value, according to the analysis results to adjust and add; the JR-S05 consumption is 0.2～0.3kg for each 100m2 treatment.

2.  PH value will rise during production and should be measured regularly. Low PH value indicates too much dragged in acidic solution and should be adjusted with ammonia water or sodium hydroxide. Adjust with Dilute acetic/sulfuric acid if PH is too high. 

3. White precipitation will occur after some time and should be removed.

 

u Packing and Storage

20kg carton pack；Protect form heating, avoid acid and alkali, keep sealed in a dry, cool place and prevent   leakage. The product shelve life is 1 year under room temperature.