CD11型鋁電解電容器

CD11型鋁電解電容器 貼片電解電容生產廠家

產品詳細介紹
產品名稱：CD110X型鋁電解電容器

產品編號：205649-964

CD110X 型電解電容器
+85℃，2000小時
體積小，性能穩定，可靠性高

主要技術性能
項目 特性
使用溫度范圍 (℃) -40~+85 -25~+85
額定電壓范圍 (V) 6.3~100 160~450
標稱電容量范圍 (μF) 0.1~15000
標稱電容量允許偏差(%) ±20(20℃,120Hz)
漏電流 (μA) I≤0.01CRUR或or 3(取較大值) I≤0.03CRUR+10
損耗角正切值 (tgδ) (20℃,120Hz)
UR(V) 6.3 10 16 25 35 50 63 100 160~250 350~450
tgδ(max) 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08 0.18 0.20

容量大于1000μF者,每增加1000μF,其損耗角正切值增加0.02.

溫度特性 (120Hz)
UR(V) 6.3 10 16~50 63~100 160~250 350~400 450
Z-25℃/Z+20℃ - - - - 6 8 15
Z-40℃/Z+20℃ 8 6 4 3 - - -

容量大于1000μF者,每增加1000μF,Z-25℃/Z+20℃阻抗比增加0.5,Z-40℃/Z+20℃阻抗比增加1.

耐久性 (+85℃)
時間 2000小時
容量變化率 ±20%初始測量值以內
漏電流 ≤初始規定值
損耗角正切值 ≤200%初始規定值


高溫貯存 (+85℃)
時間 1000小時
容量變化率 ±20%初始測量值以內
漏電流 ≤初始規定值
損耗角正切值 ≤200%初始規定值

試驗后:施加額定電壓30分鐘,于24至48小時之間測試.



外形尺寸表 D ±0.5 ±1.0
5 6.3 8 10 12.5 16 16
L+2.00 11 11 11.5 12.5,16,20 20,25 25,31.5 35.5
F±0.5 2 2.5 3.5 5 7.5
d±0.1 0.5 0.6 0.8



標稱電容量、額定電壓、額定紋波電流與外形尺寸對應表
UR(V) 6.3 10 16 25 35
CR(μF) ΦDXL(mm) I~(mA)* DXL(mm) I~(mA) DXL(mm) I~(mA) DXL(mm) I~(mA) DXL(mm) I~(mA)
4.7 5X11 25 5X11 30
10 5X11 40 5X11 40 5X11 45
22 5X11 50 5X11 55 5X11 60 5X11 60
33 5X11 60 5X11 65 5X11 70 5X11 70 5X11 80
47 5X11 70 5X11 75 5X11 80 5X11 90 6.3X11 110
100 5X11 100 5X11 110 6.3X11 140 6.3X11 150 8X11.5 190
220 6.3X11 170 6.3X11 190 8X11.5 240 8X11.5 260 10X12.5 330
330 6.3X11 210 8X11.5 270 8X11.5 300 10X12.5 380 10X16 450
470 8X11.5 300 8X11.5 330 10X12.5 420 10X16 500 10X20 590
1000 10X12.5 530 10X16 620 10X20 740 12.5X20 1000 12.5X25 1050
2200 12.5X20 990 12.5X20 1050 12.5X25 1200 16X25 1500 16X31.5 1750
3300 12.5X20 1150 12.5X25 1350 16X25 1650 16X31.5 1900 18X35.5 2250
4700 16X25 1700 16X25 1800 16X31.5 2100 18X35.5 2450
6800 16X25 1900 16X31.5 2200 18X35.5 2600
10000 16X31.5 2250 18X35.5 2750
15000 18X35.5 2900



UR(V) 50 63 100 160 200
CR(μF) ΦDXL(mm) I~(mA) DXL(mm) I~(mA) DXL(mm) I~(mA) DXL(mm) I~(mA) DXL(mm) I~(mA)
0.1 5X11 5 5X11 5
0.22 5X11 7 5X11 8
0.33 5X11 9 5X11 10
0.47 5X11 10 5X11 10 6.3X11 10 6.3X11 10
1 5X11 15 5X11 15 6.3X11 15 6.3X11 15
2.2 5X11 20 5X11 25 6.3X11 20 6.3X11 20
3.3 5X11 25 5X11 30 8X11.5 35 8X11.5 35
4.7 5X11 30 5X11 35 5X11 35 8X11.5 40 10X12.5 50
10 5X11 45 5X11 50 6.3X11 60 10X12.5 70 10X16 75
22 5X11 70 6.3X11 85 8X11.5 110 10X20 120 10X20 120
33 6.3X11 110 6.3X11 100 10X12.5 160 12.5X20 180 12.5X25 190
47 6.3X11 120 8X11.5 150 10X16 210 12.5X25 230 12.5X25 220
100 8X11.5 210 10X12.5 260 12.5X20 380 16X25 400 16X31.5 430
220 10X16 400 10X20 460 16X25 720 18X35.5 730 18X40 760
330 10X20 540 12.5X20 650 16X25 880
470 12.5X20 740 12.5X25 850 16X31.5 1150
1000 16X25 1350 16X31.5 1550
2200 18X35.5 2100



UR(V) 250 350 400 450
CR(μF) ΦDXL(mm) I~(mA) DXL(mm) I~(mA) DXL(mm) I~(mA) DXL(mm) I~(mA)
0.47 6.3X11 10 6.3X11 10
1 6.3X11 15 8X11.5 15 8X11.5 15 10X12.5 15
2.2 8X11.5 25 10X12.5 30 10X12.5 20 10X16 25
3.3 10X12.5 35 10X12.5 35 10X16 35 10X20 35
4.7 10X12.5 40 10X16 45 10X20 45 12.5X20 45
10 10X20 75 10X20 75 12.5X20 75 12.5X25 75
22 12.5X25 140 12.5X25 140 16X25 140 16X31.5 140
33 12.5X25 170 16X25 200 16X31.5 190 18X35.5 200
47 16X25 240 16X31.5 260 18X35.5 260
100 18X35.5 440


*額定紋波電流 (+85℃,100Hz或120Hz)

CD11型鋁電解電容器 貼片電解電容生產廠家

貼片電解電容器使用說明 Notes for use of aluminum electronic capacitors
1.在電器回路不清楚或不明確線路之極性時，則建議使用無極性電解電容器。 1.lf circuit polarities are uncertain, Non-polar capacitors are recommended.
2.無極性(或二極性)電解電容器，可使用在極性轉換的回路或直流回路上。 2.Non-polar (or Bi-polar) capacitors can be used in polaritiy- changing circuits or DC circuits.
3.單極性電解電容器只能使用在直流電路上，其極性必需標明在適當之位置或在導針/端子之旁邊。 3.Polarized capacitors can be used in DC circuits only. Its polarity must be marked on the proper side of wire/terminal.
4.電解電容器應儲存于低溫及干燥之處所。 4.Capacitors should be stored at a place of cool and dry.
5.電解電容器不可使用在周圍溫度超過標示之使用溫度范圍。 5.Capacitors cannot be used in a place of ambient temperature exceeding its marked temperature.
6.電解電容器不適用于超過可容許紋波電流范圍之回路之上，假如有需要耐高溫紋波電流之電解電容器，請與我們洽商詳情 6.Capacitors cannot be used in a circuit where ripple current exceeds its allowed range. Please contact us if you have requirement for high temperature and ripple current capacitors
7.電解電容器經長久儲存，如果漏電流超出規格值，使用前應以額定電壓重新再老化30~60分鐘。 7.lf capacitors have been stored for a long time and its leakage current exceeds the specified value, please recharge for 30 to 60 minutes with rated voltage before using.
8.電解電容器一般品不適用于驟然間之充放電，如需使用在快速充放電的場合，請與我們洽商。 8.Capacitors cannot be used in a circuit charge or discharge, lf use in a circuit of sudden charge is required, please contact us.
9.使用于電解電容器之工作電壓，
不得超過額定電壓。 9.Application of wong voltage to capacitors should not exceed its rated voltage.
10.為了保護電解電容器之內部結構，其導針或端子不容許過分之拉力或承受的拉力，請參考JIS C 5102。 10.ln order to protect the internal structure, ydcon capacitors cannot be applied with over pull-force. Please refer to JIS C 5102.
11.電烙鐵應與電容器塑膠套管保持適當距離，以防止過熱造成塑膠套管破裂。 11. Soldering iron should be kept in a suitable distance from vinyl sleeve of capacitor in order to avoid sleeve crack.
12.電解電容器經波峰焊錫之程序，其焊錫槽之溫度不容許超過260℃±10℃，時間10秒鐘。 12.For peak soldering , the solder temperature should not exceed 260℃±10℃ for 10 seconds.
13.為了保護塑膠套管、印刷標示以及封口材料不被破壞，電解電容器不得以滷化化學藥品或類似溶劑，作為電解電容器洗滌之用，如三氯乙烯、二甲苯類或酮類等。 13.In order to protect PVC sleeve, printed marks and sealing material, capacitors can not be cleaned with  halogenated chemicals or similar solvent such as trichlorethylene, Xylene or Acetone, etc.
14.本公司一般規格之電解電容器，其品質依照JIS C 5141 標準。 14.Quality of our capacitors is in accordance with JIS C 5141.
15.本公司之信賴性試驗方法，JIS C 5102 標準。 15.Reliability test methods for our capacitors are
in accordance with JIS C 5102.
16.本公司在生產過程中不使用破壞臭氧層之藥品。 16.None of Ozone Depleting Chemicals (ODC) is used in any manufacturing processes of yadacon Company.